Calculate how many square feet of flooring or tile to order, plus the box count, with a waste factor. Works for hardwood, laminate, vinyl plank, and tile. Free calculator for contractors.
Enter the room length and width, then pick a waste factor. The calculator gives you the total square footage to order (with waste included) and an estimated box count assuming 20 sq ft per box — adjust to the actual sq ft per box on the packaging.
The flooring calculator estimates the total square footage of flooring or tile to order for a single rectangular room, with your chosen waste factor already applied, and converts that area into an estimated box count. It also reports the net floor area (length × width) so you can cross-check against your tape measure. Enter the room length and width in feet, pick a waste factor, and the tool returns the total square feet to order, the box count, and the net area. It works for hardwood, laminate, vinyl plank, and tile — anything sold by the square foot or by the box.
The calculator handles one rectangle at a time. For an L-shaped room, a room with a closet, or an open-plan space with several zones, break the floor into separate rectangles, run the calculator for each one, and add the total square footage together before ordering. Measure each rectangle’s length and width at its longest and widest points, apply the same waste factor to each, and sum the results. This avoids the error of treating an irregular room as a single rectangle, which underestimates the material for the extra cuts at the offsets.
For a room with a bump-out or bay window, measure the main rectangle first, then measure the small rectangle of the bump-out separately and add it. For stairs, measure the tread and riser of one step, multiply by the number of steps, and add that to the room total — stairs usually need a higher waste factor (15–20%) because of the many angled cuts.
Flooring is sold by the square foot, so the core calculation is the floor area: net area = length × width. The calculator then applies your waste factor to get the total square footage to order: total sq ft = net area × waste factor. The waste factor covers cuts, offcuts, defects in the material, and pattern matching — it is not optional, because you can never use 100% of every board or tile.
The waste factor depends mostly on the layout pattern, because complex patterns create more offcuts that cannot be reused. Use these as a starting point:
The calculator offers 5%, 10%, and 15% presets. For a 20% herringbone job, run the tool at 15% and then add roughly 5% more by hand, or simply order one extra box beyond the 15% result.
The calculator divides the total square footage by 20 square feet per box to estimate the box count — a common carton size for laminate and vinyl plank. Real coverage per box varies widely by product: hardwood boxes often hold 18–25 sq ft, laminate 15–22 sq ft, vinyl plank 18–30 sq ft, and tile cartons range from 5 to 20 sq ft depending on tile size. Always check the square feet printed on the actual carton you are buying and recalculate if it differs from 20.
To adjust the box count for a different carton size, divide the total square footage by the sq ft per box on your packaging and round up. For example, if the tool says 330 sq ft and your cartons hold 22 sq ft, you need 330 ÷ 22 = 15 boxes.
You cannot buy a partial box, so the calculator always rounds the box count up to the next whole box. If the math gives 16.2 boxes, you buy 17. Never round down to save the cost of a box — running short mid-install means stopping work, and matching the dye lot on a later purchase can be difficult or impossible. Order one or two extra boxes beyond the calculated number for future repairs, especially for natural products like hardwood where color and grain vary between production runs.
Floor a 20 ft × 15 ft room with a straight-lay vinyl plank and a 10% waste factor — the calculator’s default values:
The calculator displays 330 sq ft to order, 17 boxes, and 300 sq ft net area — matching the math above. If your cartons actually hold 22 sq ft, recalculate: 330 ÷ 22 = 15 boxes. For a diagonal lay in the same room, switch to 15% waste: 300 × 1.15 = 345 sq ft, and 345 ÷ 20 = 17.25, rounded up to 18 boxes.
Split the floor into two rectangles, run the calculator for each one with the same waste factor, and add the total square footage together. Then divide the combined total by the sq ft per box on your packaging and round up. Never treat an L-shape as a single rectangle — it underestimates the cuts at the offset.
Use 10% for a straight lay in a rectangular room, 15% for a diagonal lay, and 20% for herringbone or complex patterns with many cuts. The calculator offers 5%, 10%, and 15% presets; for a 20% job, run it at 15% and add roughly one extra box, or add 5% to the result by hand.
20 sq ft is a common carton size for laminate and vinyl plank, so it gives a useful estimate. Real coverage per box varies by product — hardwood, tile, and vinyl cartons all differ — so always check the sq ft printed on your actual packaging and divide the total square footage by that number, then round up to whole boxes.
Multiply the room length by the width to get the net area, then apply a waste factor (10% is standard for a straight lay). The result is the total square footage to order. Divide by the sq ft per box on the packaging and round up to whole boxes.
Use 10% for a straight lay in a rectangular room, 15% for diagonal layouts, and 20% for herringbone or complex patterns with lots of cuts. The waste factor covers cuts, defects, and pattern matching.
Yes — enter the room dimensions and a waste factor. For tile, use 10% waste for a straight lay and 15–20% for diagonal or complex cuts. The box count assumes 20 sq ft per box, so adjust to your actual tile carton size.
Pair this estimate with a trade-specific inspection checklist for a clean, verified close-out: Flooring punch list checklist.
Create your free QuickPunch account →